Vệ sinh Pentacon auto 2.8/135(ST)

Đây là dòng len được nhiều nười biết đến và ai đã từng nghĩ tới M42 thì đều thấy thèm thuồng được cầm nó 1 lần, hiện nay có rất rất nhiều người đang sở hữu em này, vì vậy tôi sưu tầm bài hướng dẫn này ...có tể sẽ giúp ích cho mọi người.

The lens.



Now placed on a light coloured cloth so that any bits (screws, springs, ball bearings, etc) can be seen. Focus has been set to infinity and the two barrels mount/base barrel and focus barrel taped together.



The back element has been protected. The 4 screws can be removed and the mount lifted off. Don'y worry about orientation - it can only go back one way.



Mount removed, screws safe and the inside of the lens. The mount can be cleaned now but there's usually not much to do.



Inside the lens.



Ball bearing after removal of the aperture ring. This time it stayed put - but it's very easy to lose it.



Aperture ring.



Close-up of the slot in the main helicoid and the guide rod. We need to mark the position of the helicoid relative to the guide rod. This was done with a scratch on the metal. The scratch is under the redline which has been added in editing.



Another view of the slot and guide rod.



Screws and guide rod after removal.



We can now unscrew the focussing helicod (which is fixed relative to the base/mount helicoid by the tape) from the main helicoid. When we started the slot (marked S) was directly opposite the two holes now indicated by red arrows. In the photograph above the focussing helicoid has been turned by just over one and one half turns and can now be lifted from the main helicoid. The position at which the two parts become separated is important and should be marked in some way. We need to start from that position when we put them back together again.



The main helicoid now exposed.



The focussing helicoid (with the base/mount helicoid) and the two pieces of tape. One piece of tape retains the ball bearing - did I mention this earlier ?

The next sequence is quite tricky to describe so I'll pause and restart after a break.

-----------

Restart.



Remember that the focus was set to infinity. We can't focus beyond infinity but we can remove the tape and focus a little before infinity (see above).



Here's the screw which stopped us focussing beyond infinity - we can now remove it...



and focus beyond infinity ....



... and this is after one whole turn and a bit ...



and this is as far as we can go.

So when we have separated the two barrels we can clean them, relubricate them and aim to reach this position when we reassemble. We then work backwards to reach the normal infinity position for the working lens.

So back to infinity and then back a whole turn we reach the position below :



This is the normal infinity position. We now work in the opposite direction and start counting COUNT=0 (above).



COUNT=1 Its beginning to come apart although you can't see it yet.



COUNT=5 Nearly there.



And this is where the two barrels come apart - this is where we start when we want to put them back together again.



Separated.

The two barrels can now be cleaned using whatever method you choose - I use petrol to remove the grease and concentrated detergent (washing up liquid) to wash away traces of petrol and grease followed by rinsing and drying in warm air (hair-dryer or fan heater). I then lightly regrease and reassemble.

I have seen some sites where the repairers (working on different lenses) do not actually grease this helicoid pair. I think that it's helpful.

You may have spotted a considerable amount of redundancy, or un-necessary description, in the account given above. However when I started disassembly I didn't know what I would find and I took down too much information rather than too little.

One more section - back in ten minutes.

--------------

Last lap - as far as my contribution is concerned.

First of all de-grease and clean the main helicoid since we are going to handle it.



Locate grub-screw and loosen. You can take it out completely but its a little difficult to put it back. If you do leave it in make sure it doesn't fall out by accident.

Unnscrew the two main sections as indicated by the arrows.



Separated.



Details of the grub-screw and the "pit" it screws into.



I was getting tired at this point so I missed a couple of pictures. Here's a picture of the cap which holds the rear element. It has been unscrewed - the element is still in place.



Here the rear element has been removed. There is another element in front of the diaphragm. I simply used a blower to blow any dust from this cavity. I cleaned the rear element replaced it and screwed the cap on. Make sure that you put the rear element back the right way round - if you know what that is - someone may have been there before you and put it back the wrong way round !



Front of the diaphragm cavity. I simply used a blower to clean it.



The pen behind this assembly is simply there to hold the lever which closes the diaphragm - so that we can see the blades. Mine were extremely clean and required no attention.



Front lens block + hood. You will need to screw in the grub screw so that they can be pushed .....



....apart.

Reassembly is obvious with re-greasing where appropriate.



Back together again.

----------

Many thanks again! I will try this soon! Now when this lens aperture works better I will probably use the lens more.

Uh, that grub-screw look reeeeally tiny on the lens.

I wonder, would I be seen as a blasphemer if I detach the hood and replace it with a rubber one? Wink Don't get me wrong, I appriciate to keep things original and the right one looks pretty, but it's in the way sometimes.

By the way, here's the two things I did on mine. I took away the screw holding the spring which opens the aperture in auto-mode, and broke (by mistake) the copperplate on the auto/manual-switch thingie.



http://forum.mflenses.com/pentacon-auto-2-8-135-partial-disassembly-and-cleaning-t9836.html

0 nhận xét:

Đăng nhận xét

 

Liên Hệ

Liên hệ Sách Nguyễn Photography
ĐC: 98 Nguyễn Viết Xuân, T.P Vinh
ĐT: 0978877999 – 0977992282
email: sachnguyen@gmail.com

Người theo dõi

Biểu mẫu liên hệ

Tên

Email *

Thông báo *